※ 引述《Santander (怎麼可以那麼帥)》之銘言：
[deleted]
: 壓引擎搭配KERS系統外，引擎尺碼必須在長150mm×寬250mm×高800mm的體積之內、最低
: 重量為155kg、最高轉速將限制在15000rpm、汽缸夾角也限定為90度及每缸4氣門設計；
: KERS系統的輸出功率則提高至120kW、重量介於20kg至25kg之間；變速系統方面，規定要
: 有八前速，而在賽季前車手必須向FIA報備所採用的齒比設定，若要在賽季中改變變速箱
: 齒比也須向FIA報備、並僅可以交換齒輪的方向進行，同時賽車必須在比賽中具備自行倒
: 車與自行發動的能力。
:
[deleted]
: → dn890221:150x250x800mm的空間可以塞下90度V6喔? 04/08 19:56
: 推 tengpojen:樓上這麼一說我才發現好像真的滿小的! 04/08 20:54
: 推 dirtyman:3個面紙盒直的疊起來= =? 04/08 21:04
: 推 bonjour10019:圖片看起來的size差不多欸 也太小 04/08 21:12
: → corlos:F1科技真是恐怖，引擎這麼小顆可以輸出這麼大的功率 04/08 21:37
: → dn890221:誰可以指點我一下以連結圖為例長寬高分別是哪三個方向嗎? 04/08 22:31
我也覺得怪怪的。所以去查了規則。
http://ppt.cc/FSWs
2014 F1 Technical Regulations - Fia
第五章是關於引擎的。
5.3 Power unit dimensions :
5.3.1 Cylinder bore diameter must be 80mm (+/- 0.1mm).
5.3.2 The crankshaft centre line must lie on the car centre line and
90mm (+/-0.5mm) above the reference plane. The power unit may only transmit
torque to the gearbox by means of a single output shaft that must be
co-axial with the crankshaft. The output shaft must rotate clockwise when
viewed from the front of the car.
5.3.3 Valve stem diameter must not be less than 5mm.
5.3.4 The power unit must be installed in the union of the volumes that exist
between two vertical planes normal to the car centre line separated by 700mm
and in a box 150mm long, 250mm wide and 800mm high which lies symmetrically
about the car centre line immediately ahead of the front vertical plane.
...
我覺得應該是指單一排汽缸的尺寸吧？...
有對這熟的鄉民可以解說一下嗎？
--
Money can't buy happiness but it can buy performance
--
[deleted]
: 壓引擎搭配KERS系統外，引擎尺碼必須在長150mm×寬250mm×高800mm的體積之內、最低
: 重量為155kg、最高轉速將限制在15000rpm、汽缸夾角也限定為90度及每缸4氣門設計；
: KERS系統的輸出功率則提高至120kW、重量介於20kg至25kg之間；變速系統方面，規定要
: 有八前速，而在賽季前車手必須向FIA報備所採用的齒比設定，若要在賽季中改變變速箱
: 齒比也須向FIA報備、並僅可以交換齒輪的方向進行，同時賽車必須在比賽中具備自行倒
: 車與自行發動的能力。
:
[deleted]
: → dn890221:150x250x800mm的空間可以塞下90度V6喔? 04/08 19:56
: 推 tengpojen:樓上這麼一說我才發現好像真的滿小的! 04/08 20:54
: 推 dirtyman:3個面紙盒直的疊起來= =? 04/08 21:04
: 推 bonjour10019:圖片看起來的size差不多欸 也太小 04/08 21:12
: → corlos:F1科技真是恐怖，引擎這麼小顆可以輸出這麼大的功率 04/08 21:37
: → dn890221:誰可以指點我一下以連結圖為例長寬高分別是哪三個方向嗎? 04/08 22:31
我也覺得怪怪的。所以去查了規則。
http://ppt.cc/FSWs
2014 F1 Technical Regulations - Fia
第五章是關於引擎的。
5.3 Power unit dimensions :
5.3.1 Cylinder bore diameter must be 80mm (+/- 0.1mm).
5.3.2 The crankshaft centre line must lie on the car centre line and
90mm (+/-0.5mm) above the reference plane. The power unit may only transmit
torque to the gearbox by means of a single output shaft that must be
co-axial with the crankshaft. The output shaft must rotate clockwise when
viewed from the front of the car.
5.3.3 Valve stem diameter must not be less than 5mm.
5.3.4 The power unit must be installed in the union of the volumes that exist
between two vertical planes normal to the car centre line separated by 700mm
and in a box 150mm long, 250mm wide and 800mm high which lies symmetrically
about the car centre line immediately ahead of the front vertical plane.
...
我覺得應該是指單一排汽缸的尺寸吧？...
有對這熟的鄉民可以解說一下嗎？
--
Money can't buy happiness but it can buy performance
--
All Comments